Washing machine errors - table with codes and explanations

Errors in washing machines detected by the equipment during self-diagnosis can be corrected independently or by contacting specialists. Regardless of who is troubleshooting, it pays to know what the codes say. Despite the fact that the faults of washing machines are basically the same, they have different designations. In this article, we will tell you which spare parts for washing machines, when broken, can lead to certain errors, and options for correcting them.

The indication of all lights is triggered when any error is detected

Washing machines can inform you about operating problems that have arisen by displaying a code on the display. If the model does not have a monitor, the indicator lights will blink

Common washing machine error codes

Error codes for washing machines are usually lettered E or F; combined symbols are also possible - PE, FE, dE, IE, OE, UE, tE and others (for the LG brand). You can find out what exactly happened to the equipment by checking the letters and numbers with the symbols that the manufacturer indicates in the instructions or on specialized websites. Depending on the type of problem, you may have to replace the heating element, thermostat, pump, or brushes and cuffs for washing machines.

Error codes for LG washing machines

Let's look at why the washing machine gives an error and how you can fix this problem:

Washing machine drain error

When the washing machine stops draining water, it could be either a single malfunction in the functioning of the module or a clogged drain pump, which just needs to be cleaned. When diagnosing equipment, you must pay attention to the electronic controller (control board), as well as the wiring and contacts in the pump circuit.

Drain error in Samsung washing machine

Error E4 in the washing machine indicates that water is not being filled. This may be due to its absence in the water supply. Check that the shut-off valve is not closed. The mesh in the water supply hose could also be clogged or the line may be kinked.

Do not confuse the errors of draining and collecting water. They signal different types of problems, and require different ways to eliminate the causes

Error heating water in washing machine

In models of various brands and models of washing machines, error 5e indicates problems with water heating. It may be too hot or, on the contrary, remain cold. In this case, the fault may be:

• Temperature sensor.
• Heating element or its contacts.
• Controller.
• Wiring.

Error heating water in Samsung washing machine

Washing machine door lock error

A washing machine with a Door error will not close the hatch, or, on the contrary, will not unlock it after washing. This can happen due to a one-time module failure or if part of the item gets caught in the locking mechanism.

In this case, washing machine errors can be corrected only after the cause of the breakdown has been identified. Depending on the malfunction you must:

• Repair door hinges or lock.

• Restore the locking device.
• Replace the control board.
• Look for damage to wiring or contacts.

Washing machine with Door error

Error - too much foam in the washing machine

If the washing machine shows the SUD error, there is too much foam in the drum. Most often, the reason for this is the greater amount of powder poured in or the processing of very fluffy or porous things. A clogged hose or drain filter may also be the culprit for this problem.

If the washing machine shows this type of error, this may indicate a malfunction of the foam and water level sensor, control board. Also, when inspecting the equipment, it is worth checking the drain pipe, which is subject to frequent blockages.

Error SUD (too much foam) washing machine

Greater foaming is possible if you use hand wash powder instead of machine wash detergent.

What does the UE code mean that the LG washing machine produces?

The UE error appears quite often in LG washing machines. It is not always indicated in the same way, which depends on the model of the device, the year of its manufacture and the characteristics of the breakdown.

Possible options:

• capital Latin letters UE;
• lowercase and uppercase Latin letter uE;
• for machines without a display: all spin lights or LEDs numbered 1 to 6 are on.

As a rule, the code appears on the display after the machine has finished rinsing things and drained the water. Normally, after these programs the spin should start, but this does not happen. The device will make several attempts to reach the required number of revolutions for spinning, after which the UE or uE error will appear on the screen.

What does it mean? The UE error means that the LG washing machine was unable to evenly distribute the load on the drum.

If a code with a small letter u (uE) is displayed on the display, this indicates that the device has detected a load imbalance and is trying to correct it on its own by adding a little water to distribute the laundry more evenly throughout the drum. In this case, the owner of the washing machine does not need to do anything.

If after some time the user notices that the small letter u changes to a capital U, then the device was not able to solve the problem on its own. Despite all the efforts of the washing machine, the imbalance could not be eliminated.

How to reset a washing machine error

If it was not possible to automatically reset the washing machine error after restoring functionality, you can do this manually. To do this use:

• "Start/Pause" button . Activate it and hold it until the indicators start flashing or a beep sounds. Usually this technique helps remove the error from the monitor.
• Test mode . If you cannot remove the inscription and lock using the buttons, use the testing function. How to run the program can be seen in the instructions, which describe the reset sequence.

Resetting an error using the Start/Pause button

Cleaning the filter

Experts note that in some cases, SM Atlant may display error F14 due to a clogged drain filter. It sounds unexpected, but the fact remains a fact. Cleaning the filter is easy.

1. Disconnect the machine from the power supply.
2. Tilt it back a little.
3. Place a flat container under the body to drain dirty water into.
4. Open the hatch, which is located in the lower right corner of the washing machine body.
5. Unscrew the filter and drain all the water.
6. Clean everything inside, rinse the filter itself and screw it back into place. Return the machine to its original position.

After cleaning the filter, try restarting the machine several times. Then run the service test as described above. If error F14 persists, then the matter is serious.

Control module test

Apparently, you can’t do it without the help of an experienced craftsman. If the above measures do not help, you will need to test the control module for a malfunction. Only a specialist can perform such an operation efficiently. Independent testing and repair of the control module can cause irreparable harm and subsequently you will definitely have to change the electronic filling. By the way, the cost of a new part is 50% of the cost of a new machine, so don’t take unnecessary risks.

You may have encountered other error codes for Atlant washing machines. If so, read the article of the same name, which is on our website, and we say goodbye to you and wish you good luck!

Interesting:

• Error codes for different dishwashers
• Bosch dishwasher errors
• Miele dishwasher errors
• Gorenje washing machine error codes
• Ariston dishwasher error codes
• Whirlpool dishwasher error codes

Reader comments

• Share your opinion - leave a comment

Errors in washing machines without display

Errors on washing machines without a display are also displayed, but they are not displayed on the monitor, but are displayed by combinations of indicators. Each set corresponds to a specific problem. If the instructions do not contain decoding codes, you can find them on the Internet.

Samsung washing machine errors without display

Error F14 in the Ariston washing machine: what to do and how to cope?

We collected the laundry, loaded it into the drum and selected a mode (program), but your unit refused to work and displayed fault F14 on its screen. Or it executes the set mode, as soon as the time to start drying approaches, then it immediately displays F14.

If the device manufacturer does not provide a display, then fault F14 is displayed using LED illumination, depending on its modification:

• Ariston Margherita modifications AL 108 D, AL 128 D displays a problem due to constant cyclic blinking of the network LED (the number of blinks corresponds to the error nomenclature, i.e. 14 times, silence plus or minus 10 seconds and repeat the cycle). The switch knob constantly rotates clockwise and produces a characteristic audible click.
• Ariston modifications AML 109, 129, etc. will notify you of a malfunction by blinking the LED indicators of auxiliary functions from the first to the third, with the exception of the last. In addition to the illumination, the door lock indicator “Lock” will blink more quickly.
• Hotpoint-Ariston modifications ARMXXL, CAWD, AVDK, etc., which are equipped with a laundry drying function, display a malfunction by flashing LEDs indicating the completion of all programs, draining, and spinning (i.e., from the second to the fourth indicator light, except for the first, countdown lead from bottom to top). In addition, depending on the series of the device, for complete notification of the specified malfunction, the entire LED panel of auxiliary modes lights up horizontally (sometimes vertically).
• Hotpoint-Ariston Aqualtis modifications AQXL, AQXF, etc., which are equipped with a drying function, display fault F14 by constantly blinking from the second to fourth LEDs, which are responsible for the temperature regime (counting only from bottom to top). (These are temperature regimes of 30, 40 and 60°C or 30, 40 and 50°C).

Problem Meaning

A breakdown with the abbreviation F14 in an Ariston or Hotpoint-Ariston unit notifies you of the lack of contact communication in the segment limited by the heating element and the electronic module responsible for controlling the washing machine (breakage of the heating element: it is covered with scale and requires replacement, or there is no contact, etc.). Sometimes a malfunction with such a code is corrected without calling a repairman.

Malfunction F14, how to fix it without professional help

• A banal automation failure. When you first discovered the F14 problem, it is not difficult to fix it. Unplug the cord from the outlet. Leave the unit without power supply for plus or minus 10 minutes. Connect, the control module will reboot, then your washing machine will safely perform its function.
• Broken contact circuit of the heating element for drying. Inspect the circuit sequence and correct communication (power) between the heating element and the software board. As a result of incorrect installation or transportation of the device, the contacts of the electric heating element may have come loose, so they need to be disconnected and reconnected.

Have you performed all the recommended manipulations, but the device still does not work? Is fault F14 still displayed? Then you need to seek professional help. Call a washing machine repairman.

You can also find out what error F23 means in a Bosch washing machine by following the link.

Source: https://TechnoSova.ru/dlja-chistoty-i-porjadka/stiralnaja-mashina/code/ariston/kod-oshibki-f14/