Atlant refrigerator how to set the temperature mode

Instructions on how to set the temperature

Automatic control of content cooling is carried out by periodic compressor starts. Methods for adjusting the temperature in Atlant refrigerators depend on the design of the model: whether the unit operates simultaneously with a common chamber and a freezer, or whether the device is a two-compressor unit. In both cases, the cold is adjusted using a mechanical or electronic regulator. The first method involves operating a rotary switch; it is simple and reliable, typical of inexpensive models. In another case, the device is equipped with an electronic display and a temperature relay.

Mechanical regulator

It is a video with digital risks from 1 to 7: with increasing values, the cold intensifies. A two-chamber unit may have more than 1 regulators. When the compressor is in unit 1, the cooling circuit for both cavities is common, and there is only one roller. You can see the temperature regulator in the Atlant refrigerator when the door is open at the top of the device. The setup procedure is as follows:

Switching on the device for the first time. Set the switch to position 2 - there will be a locking click.
Decreasing degrees is a translation by a certain number of divisions. The compressor will work continuously if you set modes 5-7. This mark is used when quick freezing is needed. Warning from the device manufacturer: prolonged operation in this mode may result in compressor failure due to overheating.
Transition from intensive cooling to standard. The operating range is indicated by positions 2-4, which corresponds to +1...+5ºС in the refrigerator compartment and -18ºС in the freezer.

Before adjusting the two-compressor Atlant, you need to make sure that the model has 2 cooling circuits. That is, each camera has its own adjustment roller. The operations are no different from those for setting the temperature regime of a refrigerator with 1 compressor. Knowing how to set up the device is also useful because proper adjustment contributes to the rational use of electricity.

Electronic regulator

In many models of Atlant refrigerators, manual switches give way to modern settings methods. The devices are equipped with electronics - a control and display unit, where the temperature set in the chambers is reflected in numbers. The small display is located outside - no need to open the refrigerator. Read more about how to correctly set the cold level with an electronic regulator:

changing the settings of the digital thermal relay is done by pressing push-button keys;
installation is possible in the range -18…- 24ºС (what temperature should be in the freezer) or +2…+8ºС (for the refrigeration cavity);
A single press of the key changes the set cooling mode by 1ºC.

How many degrees should be in each of the refrigerator compartments can be seen on the display. If the household appliance has two compressors, any of the chambers can be turned off; The digital display is divided into 2 zones, each of which reflects the state inside the device. The temperature is set by 2 adjustment blocks.

Step-by-step instruction

Are you faced with the question - how to set the temperature in the Atlant refrigerator? In fact, everything is extremely simple. To regulate the temperature, it is important to follow the recommendations below from manufacturers and experts.

In refrigerators of the Belarusian brand Atlant, a special switch is provided for its installation and change - a thermostat, which turns in two different directions. There is a dial marked around it, making it easier to set the desired value. It usually has a 7-point scale:

0 (device compressor disabled);
1 (minimum value);
7 (maximum value).

The manufacturer recommends that equipment owners set the dial to a value from 2 to 3. This is a gentle temperature regime in which food products retain their original appearance and freshness for a long time, and also do not freeze.

Note! When you turn on the device for the first time, you should not immediately select the maximum temperature. When the thermostat is turned to “5”, the compressor of the device operates in continuous mode, which can cause its failure or significantly reduce its service life.

When regulating the temperature, it is important to pay attention to the microclimate in the room. In hot weather, you should set the thermostat to position 1 or 2, which will minimize the load on the compressor and will not lead to overheating.

Note! To extend the shelf life of products, it is important to properly place them inside the refrigerator compartment. For example, meat, poultry, fish and various types of cheese are stored at 1-3 degrees, sausage - 2-4, and dairy and fermented milk products - 3-5. At the same time, it is best to place fruits (except for imported exotic ones) in the warmest place.

By following these recommendations from the manufacturer and the advice of experienced experts, you can extend the life of your equipment and the shelf life of various products.

by Boris Kornilov 294,803 views

Millions of people love cartoons, but only a few of them know what unites animation and an ordinary household refrigerator. Of course, with the help of the latter you can cool any drink and drink it with pleasure while watching an animated film. And only animation creators put plasticine figures of future characters in the freezer so that they do not melt from high temperatures and, probably, the ardent love of fans. After all, it is these three-dimensional and plastic figures that should help cartoonists create their next masterpiece.

But this is in the film industry, but in real life, it is not the fate of the cartoon character that depends on the temperature of the refrigerator, but the safety of our products. Housewives know that for proper storage of food, the temperature in the refrigerator must be different:

From +1 to +3 - for meat, fish, eggs.
From +2 to +4 - for sausages and culinary products.
From + 3 to + 5 - for soups and dairy products.

The more complex the technique, the wider the choice of settings and the greater the likelihood of making a mistake. For example, Samsung or Bosch produce models with separate adjustment of the refrigerator and freezer compartments. There is only one regulator in Gorenje devices, and it allows you to select the temperature mode from the “Min” to “Max” position. How is the temperature regulated in the Atlant refrigerator, single- and double-chamber?

Optimal temperature

A product placed for temporary storage in a refrigerator has a shelf life and conditions for the degree of cooling established by the manufacturer. These indicators vary, and need to be regulated according to the prevailing food products. To find out what temperature should be in the desired refrigerator compartment, you need to read the text on the packaging of stored dairy products. Based on the set of storage conditions recommended by the manufacturer, the optimal temperature regulation is determined, in accordance with which the degrees in the chambers need to be adjusted.

Refrigerator

The internal space of a large chamber can be divided into zones: the upper shelves are for already prepared food, the lower one is for raw meat or fish, vegetables, and fruits. Before setting the general temperature for the entire volume of the chamber, determine the level of cold that is suitable for most of the products loaded into the refrigerator. The following indicators are used for calculations:

culinary products, sausages - within +5...+8ºС;
milk, kefir, yoghurts, ready-made soups - in the range of +3...+5ºС;
raw meat, fish, eggs - 0...+3ºС.

How to set the temperature in the Atlant refrigerator

The manufacturer's line includes single-chamber freezer cabinets, and those included in the general complex, two-chamber cabinets with a refrigeration cabinet. In each case, the instructions describe exactly how to adjust the temperature in the Atlant refrigerator of each model. To configure, use the control button + mode adjustment in the refrigerator compartment or a rotary wheel with graduation. What temperature in a particular refrigerator compartment can be measured with a thermometer and make sure that the regulator corresponds to the actual position.

It must be remembered that setting the temperature in a two-chamber Atlant refrigerator with one compressor is a parameter that allows you to regulate only a complex decrease or increase in temperature in the entire system. How to set the indicator correctly depends on the load on the cameras. The most economical mode of operation of the device is if it is loaded to 2/3 of the volume.

If a problem arises, the refrigerator freezes, most likely the temperature relay sensor needs to be replaced. During normal operation of the thermostat, the temperature in the refrigerator compartment will not drop to minus.

The importance of setting the optimal temperature in the refrigerator compartment

Almost all food products retain their freshness and maximum amount of vitamins at ambient temperatures ranging from 2 to 5 degrees Celsius. All domestic and foreign refrigerator manufacturers set this value in their products by default.

But some models of equipment have a built-in regulator that allows you to change this parameter in the freezer/refrigerator compartment. However, it is important to know that if the value is set low, the food will freeze and quickly lose all its nutrients.

How to set the temperature in a two-chamber Atlant refrigerator according to instructions

In a two-compartment refrigerator with one compressor, a common refrigeration circuit is created for the freezing and cooling zones. Changing the settings of one of them will introduce an imbalance in the system. Therefore, the instructions for the temperature mode in the Atlant two-chamber refrigerator provide for changing the level with one manual regulator, with graduation points 1-7. In positions 2-4, the settings of the refrigerator and freezer correspond to the standard, what should be the temperature - in the refrigerator 1-5 0 degrees, in the freezer - minus 18 0 C.

Instructions for setting the temperature in the Atlant refrigerator indicate exactly where the temperature regulator is located. The manufacturer warns that increased cooling of the chambers in modes 5-7 may result in compressor failure due to overheating during continuous operation. It is necessary, after freezing the food, to return to the normal position (2-4) on the temperature regulator in the Atlant refrigerator. How to set and adjust the position of the wheel can be seen in the photo when using two compressors.

New wave series with electronic control

This series of refrigeration equipment is equipped with the most modern electronics, including separate temperature control and various operation indicators. When the refrigerator is connected to the network, the operating parameters of the freezer and refrigerator compartments are displayed on the control panel. The electronic unit is also equipped with an alarm system that notifies about prolonged (over 1 minute) door opening, a system for shutting down the refrigerator in case of an excessive voltage drop (below 170) and increase (over 260 volts).

Adjusting the temperature with this choice of functions is quite simple: the freezer temperature control button is located on the control panel on the left. The adjacent two-position window reflects the settings. The manufacturer's recommended temperature is about -18 degrees.

Setting the temperature of the refrigerator compartment is also not difficult: the temperature selection button is located on the control panel on the right, near the single-position display window of the main chamber of the device. By pressing this key, the mode recommended by the instructions is set. What temperature should the Atlant refrigerator be? Optimal - in the range from +3 to +5 C.

If there is a failure in the temperature mode, this will be reflected on the panel

How to set the temperature in a two-compressor Atlant refrigerator

A two-compressor refrigerator has 2 cooling systems. The freezer and refrigerator compartments are independently adjustable. However, jumpers are provided to temporarily connect both systems to one motor in case of an emergency. The temperature in each chamber of the Atlant two-compressor refrigerator is regulated by a separate graduated regulator. The standard operating position is in the range of 3-5 for cabinets. Each independent department can be turned off, but the refrigerator cannot perform the functions of a freezer, and vice versa.

What to do if Atlant does not freeze?

Like any electronics, Atlant cannot be turned on immediately after transportation. Before starting, it is recommended to wait from 8 to 16 hours: when tilting and vibrations, which are inevitable when transporting a refrigerator, the oil in the compressor leaves its workplace. After the required time has passed, the refrigerator can be turned on and the temperature setting can be set.

After the first start-up, the device gains temperature and enters normal operation throughout the day. If after this time the temperature inside any of the chambers of the refrigeration unit does not correspond to the specified mode, you will have to contact a specialized service center.

What is the temperature in the freezer of the Atlant refrigerator?

If the refrigerator is small, the freezer compartment and refrigerator are hidden behind one door, the temperature in the chamber can be -3

-12 0 C. However, modern standards dictate that in the Atlant refrigerator the temperature is considered to be 18 0 C. The 3-star marking is used on the label and in the instructions. When using electronic adjustment, you can set the temperature in the Atlant refrigerator independently for each chamber. In this case, you should adhere to the standard to avoid breakdowns.

First start

So, having bought a new refrigerator or repaired an old one, the user brings it home and, in most cases, starts the unit. There is no need to do this. Especially if the temperature outside is sub-zero. Any household appliance that has been outside in sub-zero temperatures or hot weather should be left at home for several hours. During this time, the mechanisms will accept the room temperature, which will allow the device to start without harm to the internal parts.

Another nuance that affects the operating time after the first launch is the number of products loaded into the chambers. The more products, the longer the refrigeration unit will cool them and reach the desired temperature. Therefore, there is no need to rush to load cameras to capacity. It is better to place some food in the new Atlant refrigerator, start the device and wait for the first shutdown.

If you need to check the performance of Indesit equipment after repair, it is better not to load the chambers with products. The device needs to be started, and without opening the door, wait until it turns off. On average, the first cycle after repair should last:

about 2 hours for large models,
for medium-sized LG refrigerators the cycle lasts 60-90 minutes,
for small ones – 30-40 minutes.

The device of a household refrigerator

How to adjust the temperature in the Atlant refrigerator

The purpose of a refrigerator is to store food for a long period. Some models are equipped with a regulator, which you can set correctly yourself. Atlant brand models are widely used due to their availability. They meet modern requirements and are equipped with a regulator. In the Atlant refrigerator, the temperature can be adjusted using an electronic or mechanical unit.

Cyclic operation of switched-on refrigerators of different models

The cyclical functioning of popular models (Atlant, Indesit, Samsung, LG) with a drip defrosting system is ensured by a thermostat. The duration of non-stop operation of the compressor depends on the set temperature and other factors. In general, the full cycle lasts longer for Atlanteans. A cyclicity coefficient of 0.37 to 0.5 is considered normal.

As for devices from the same manufacturers with the No Frost system, after the cooling and freezing process, the defrosting mode is activated. The latter is carried out thanks to the evaporator electric heater. On average, the working cycle lasts from 9 to 16 minutes. Moreover, cooling occurs within 2–5 minutes, the rest of the time is spent on thawing.

How many degrees should it be

The temperature in the refrigerator is maintained by a combination of various components, including the compressor. The frequency of its activation and the duration of operation determine the temperature inside the chamber. Different products must be kept under different conditions:

Meat, fish and eggs are stored at +1…+3°С.
Dairy products and soups do not spoil in an environment with temperatures ranging from +3...+5°C.
Culinary and sausage products are stored at +5...+8°C.

The more complex the technique, the wider the choice of settings. The Atlant brand produces a large number of refrigerators with main and freezer compartments, allowing you to store food in various conditions.

In the refrigerator compartment

The main refrigerator compartment is used to accommodate most products that do not need to be stored for an extended period.

The temperature in the refrigerator should be in the range of +3...+8°C.

It is difficult to set the exact temperature for stored products, since the recommended conditions may vary significantly. As the indicator decreases, the device begins to work more, so energy costs increase significantly.

In the freezer

The freezer is designed for deep freezing and long-term storage of contents. Therefore, the cold is maintained at -16...-24°C. When considering what temperature should be in the freezer, it is worth considering that everything depends on the task at hand. The features are as follows:

It is difficult to preserve vegetables and fruits at home. In this case, deep freezing is not required, since after defrosting the basic properties may change.
For fish and meat, the lowest value is selected. Such products tolerate deep freezing well and do not lose their properties after thawing.

The temperature in the freezer is maintained due to high-quality insulation and periodic activation of the compressor, which supplies cold. To reduce costs, it is recommended to open the door infrequently, as cold air will escape out.

What affects the operating (cooling) period of a refrigerator?

What should be the surface for installing the device?

Improper installation of refrigeration equipment can lead to rapid failure. Therefore, it is important to pay attention to the evenness of the surface on which it will be placed. The adjustable feet will help you level the unit if there are slight uneven floors. In addition, the device must be located at a decent distance from heating radiators and a gas stove.

The importance of following the rules for the first connection of the refrigerator to the electrical network

When connecting for the first time, you must comply with a number of standards, which will extend the life of the device:

After delivery of the unit, it should be connected to the network no earlier than 3–4 hours later. The specified time will allow it to adapt to the temperature conditions of the room, which is especially important if the refrigerator was purchased during the cold season.
Use a surge protector if the outlet is not grounded. If there are constant voltage drops in the electrical network, it makes sense to connect through a stabilizer.
The first cycle is carried out without placing products.

Why is it important not to overload the refrigerator with food?

Failure to distribute food evenly in the chambers may interfere with the circulation of cold air. For this reason, the products will not be able to receive proper cooling and will begin to deteriorate. Overcrowding will cause the temperature on the lower shelves to rise.

How to set the temperature in the Atlant refrigerator

For a long period, refrigerators were produced that supported only one temperature mode, and the presence of an adjustment function was not provided. The setting allows you to regulate energy consumption and the degree of freezing of the contents. All adjustment devices can be divided into two main categories:

Mechanical. In this case, the adjustment involves changing the position of the rotary disk, above which the scale is located. A similar mechanism is installed on many budget models, because it is easy to use and reliable.
Electronic. The device is represented by a digital panel; installation provides for indicating the mode or temperature. Electronic control units can be implemented in a variety of ways; the modern offer is represented by a large display.