How to clean a vape vaporizer

What and how to clean

The last element is otherwise referred to as an evaporator; it, together with power, determines the generation of vapor, but how to clean the evaporator of an electronic cigarette?
In this case, three care options are used:

  1. Flushing.
  2. Burn.
  3. Cleaning by rinsing with an ultrasonic bath.

But how to clean the evaporator correctly? Before washing the part, it is necessary to blow it out. This should be done so that the liquid does not remain. In this case, it is important to wait for the atomizer to cool down, since it is absolutely impossible to clean a hot one.

If the evaporator is too dirty, you can’t just wash it with water; you’ll need diluted alcohol. Here you should leave the part in alcohol for several hours, and it can easily be replaced with Coca-Cola. After this time, you can wash the evaporator with water, but only then blow it out.

The most modern treatment is an ultrasonic bath, which is used to clean jewelry. It is a very inexpensive device that is easy to buy. It is simply necessary to wash your electronic cigarette periodically, as this will keep the device in working condition for a long time.

It is dangerous to use the burning method, since it is used only if it is not possible to wash the spiral in any other way.

This often cannot be done, as this leads to the device being damaged.

The procedure for carrying out this procedure is as follows:

  1. The evaporator must first be disconnected from the battery.
  2. Blow out the atomizer.
  3. Wash with a stream of water.
  4. They're blowing again.
  5. Remove the cartridge.
  6. Connect the evaporator to the battery.
  7. Click on activation and leave it for literally five seconds.
  8. The appliance is cooling down.
  9. Press power again and repeat this procedure about fifteen times.

It is important that the button is not pressed for longer than five seconds. After burning is completed, the cooled evaporator should be connected to the empty cartridge.

After this, you should slowly inhale several times, but do not inhale the steam, but release it immediately through your mouth. Only after this can you fill the cartridge and smoke the electronic cigarette normally.

When it comes to batteries, in order for them to work properly, you need to follow some simple rules:

  1. The first charge lasts twelve hours.
  2. The battery must be fully charged.
  3. Do not allow the battery to be filled with liquid.
  4. Under no circumstances should the battery be allowed to remain discharged for a long time.

All maintenance involves wiping the battery with a dry cloth.

Now it is clear how to wash the evaporator of an electronic cigarette and how to care for the other parts of this device so that it functions for a long time without interruption.

No matter how expensive your electronic cigarette is, you cannot do without periodic cleaning of the main components of the device. When using the vape after some time, carbon deposits begin to form on the evaporator coil. When heated, this coating emits a burning smell, which significantly spoils the aroma of the escaping steam. Also, carbon deposits on the coils of the heating element interfere with normal heat transfer, as a result of which it overheats and may fail.

How not to clean an electronic gadget

We figured out how to clean the vaporizer of an electronic cigarette and care for its other parts. Now you should figure out what you should not do when using and cleaning this accessory:

  • use chemicals and solvents, they will leave an unpleasant “taste” that is impossible to cope with;
  • overheat the atomizer during a “dry run” and use a voltage higher than that recommended for the accessory;
  • wash the parts of the cigarette under running water; the components can only be soaked;
  • assemble the accessory after cleaning, when the parts have not yet dried.

By following these recommendations, you will keep your device in working condition for a long time.

Consequences of improper care

Are electronic cigarettes just a fad or the way of smoking of the future? Be that as it may, today many smokers are switching to electronic devices. Pleasant draft, aromatic vapor that does not make those around you wince, no need to shake off the ashes - these and other advantages make them a profitable alternative to regular tobacco.

E-cigarettes are refillable devices, and there are both pros and cons to that. Among the disadvantages is the fact that the device requires careful handling, as well as timely cleaning. But why and what do you need to clean a seemingly simple device? Let's briefly consider the principle of operation of e-cigarettes.

  • reduction in the volume of steam or its complete cessation;
  • difficulty traction;
  • the appearance of foreign tastes or a burnt taste.

If you have at least one of the listed problems, you definitely need to clean the device. Many people wonder how to maintain an electronic cigarette, whether it can be washed in water - we will examine all these nuances in detail below.

Operating principle of an electronic cigarette

Of course, not everything about modern electronic cigarettes has been fully studied, but the advantages of using them compared to regular tobacco are obvious.

And yet: why does a person need an electronic cigarette? Many people think about this, but it is impossible to give a definite answer in this case.

This invention was patented in Hong Kong in February 2004. Chinese scientist Hong Lik, who works in the pharmaceutical field, has invented an electronic cigarette to safely simulate smoking regular cigarettes.

The death of his father from lung cancer pushed him into this area of ​​research and to the search for an alternative to traditional tobacco smoking.

We suggest you familiarize yourself with Hard water boiling

As a result, he came up with a modern electronic cigarette, the principle of which is to generate nicotine into vapor. The electronic version does not cause harm to health, unlike tobacco products.

The whole truth about electronic cigarettes is that they are not harmful to health when consumed in moderation, help to get rid of nicotine addiction and give a lot of pleasant sensations.

When to start cleaning your vape

Such a device is a structure consisting of a cartridge (tank) and an atomizer. Cleaning it is a little different, but nothing difficult about it.

The clearomizer must first be disconnected from the battery. This part of the device should be properly cleaned after disassembling it.

First, disconnect the block from the tank, then wipe the part with a dry cloth. Remaining liquid must be removed.

The next step is to disassemble the atomizer. You need to remove the silicone part and the top, unscrew the heating element and pull out the bottom part of the atomizer with tweezers.

Having taken out all the parts, wipe them with a napkin, rinse with water and dry. Then reassemble in reverse order.

Clearomizers are different and can also be understood differently, so don’t throw away the instructions. It describes in detail how to disassemble it to clean it.

The vaper is required to closely monitor the operation of the vaping device and pay attention to the slightest signs of malfunctions in the operation of the electronic cigarette. There are several signs, when they appear, you need to start cleaning the gadget:

  • the amount of steam has decreased with a sufficient amount of liquid in the cartridge and with a well-charged battery;
  • a burning taste appeared when vaping;
  • steam is not generated at all or is released in small portions;
  • the electronic cigarette overheats;
  • To tighten it, you have to make more effort than was previously required.

The appearance of at least one of the listed signs is a signal to start cleaning the vape, which should be done according to certain rules.

A clearomizer is a design that combines both a cartridge (tank) and an atomizer. To clean the clearomizer, it must be disconnected from the battery module and disassembled. Since there are a large number of models of masters, the principles of servicing them in each case may differ.

Kangertech Evod

To clean the clearomizer from a Kangertech Evod electronic cigarette with eGo thread, do the following:

  • disconnect the heater block from the tank;
  • Wipe this part of the miser well with a napkin to remove any remaining liquid;
  • remove the silicone seal and disconnect the top part of the atomizer;
  • after this, unscrew the heating element itself with the wick;
  • Use tweezers to pull out the bottom of the atomizer.
  • do the same to remove the rubber insert that separates the spiral contacts from shorting;
  • After removing the tab, blot it well with a napkin to remove dirt;
  • next, using the same tweezers, remove the heating element from the base by pulling the wick;
  • now, using a napkin you need to clean the base;

All parts of the atomizer can also be washed in warm water without using detergents, and then dried with a hairdryer.

When cleaning your clearomizer, you need to replace the wick. This clearomizer uses silica cord as the wick. You can purchase it at the store where you bought your vape or a similar store that sells accessories for electronic cigarettes. It is threaded through the spiral and, together with the latter, is inserted into the base, so that the liquid supply holes are not blocked.

Once the evaporator unit is fully assembled, cut off the excess cord with scissors flush with the body.

Now you can fill the tank with liquid and assemble the clearomizer.

I just 2 / melo 2

The clearomizer of the Eleaf I just 2 / melo 2 model is slightly different from the clearomizer discussed above, so cleaning it looks like this.

  1. Unscrew the liquid tank from the atomizer.
  2. Now unscrew the evaporator itself from the mod body.
  3. Remove the top part of the atomizer - it can be pulled out quite simply without using tweezers.
  4. Afterwards, you need to pull out the rubber bushing.
  5. Next, in the hole you will see the antennae of the heating element, which need to be pressed a little. Using a thin object, push the spiral (from the side where the elastic was) out. The housing in which the heating element was located must be cleaned with a cotton swab or rinsed with water, then blown and dried.
  6. After removing the spiral, you will see that cotton (wadding) is wound around it. Remove the wick from the heating element.
  7. If the wick is clogged or slightly burnt, it must be replaced by cutting a strip of the same width from a cotton pad and wrapping it around the coil.
  8. Pay attention to the coils of the heating element. If carbon deposits are visible on them, then ignite the heating element with a lighter (it is better to use a turbo lighter). The coils should be heated until all the coating on them burns off and it becomes red hot.
  9. Assembly is carried out in reverse order. Do not forget to separate the legs of the spiral with a rubber bushing, otherwise there will be a short circuit. Also, after completely assembling the vaporizer, saturate the cotton with vaping liquid. If this is not done, then after you turn on the vape, the dry wick will begin to burn.

Burning the heating element must be done when you feel a burning taste while vaping or notice that a small amount of steam is being released (provided that the battery is charged and there is liquid in the tank).

The maintenance procedure for the EGO-T clearomizer is as follows.

  1. To start cleaning this clearomizer, you also need to separate it from the battery pack, and then wipe the contacts of the mod well with a napkin. Soot will form on them over time.
  2. Next, take the ego-t clearomizer and unscrew the mouthpiece.
  3. After laying a napkin to catch any residual fluid that flows out, unscrew the evaporator heating element.
  4. After unscrewing the heating element of the atomizer, the evaporator itself will fall out onto the napkin, on which the wick cord is clearly visible.
  5. Free the evaporator and wick antennae from the old liquid using a napkin, then unscrew its lower part.
  6. Use a cotton pad or napkin to blot off any residual liquid on this part. At this stage, cleaning the evaporator is completed.
  7. Next, you need to clean the heating element from carbon deposits. It should be wiped both from the side where it is connected to the mod and from the opposite side. Be careful when wiping, do not lose the silicone seal placed on top of the heater.
  8. The next step is to clean the fluid container. It can be washed in warm water and wiped inside with a cotton pad.
  9. Finally, you need to rinse and wipe the mouthpiece (it also has a silicone pad).

After washing, first blow off the parts, then remove all remaining liquid with a napkin, cotton swab or cotton pad.

Reassembly is carried out in the reverse order, after which the ego-t electronic cigarette will be ready for vaping.

There are other types of clearomizers, since technological progress does not stand still. But the methods for cleaning them do not differ significantly from those given above and are intuitive. As a last resort, you can look at the instructions for the electronic cigarette you purchased.

Prevention of contamination and damage

Care and regular cleaning of your e-cigarette can extend its lifespan. In order for the device to delight you with aromatic smoke for a long time and with high quality, follow a few simple rules:

  • Read the instructions before changing parts of the device.
  • Purchase refill fluids, as well as other components, only from trusted places. The seller must have the appropriate license for the product.
  • Clean your cigarette regularly—every two to three months. It is also recommended to clean the cartridge every time before changing the flavor of the liquid so that different flavors do not mix.
  • Do not add too much liquid for refilling.
  • While smoking, do not take too deep breaths to prevent the device from overheating, otherwise the vaporizer in the e-cigarette may need to be replaced.
  • Do not use your e-cigarette in cold weather.
  • Keep the device charged as much as possible.

As you can see, caring for an electronic cigarette is not that difficult. It is enough to use a few simple tips, and a regularly serviced electronic gadget will not create problems.

We hope that our article helped you get answers to many questions - how to clean the vaporizer, how to handle different types of e-cigarettes, how to care for your device.

There are a variety of methods for cleaning an atomizer. This should be done regularly and even new ones should be cleaned - this way they will last longer. But in any case, it is better to keep several spare ones on hand in case you do not have time to rinse properly or one of them fails.

Many vapers are not interested in the question of how to clean the vaporizer of an electronic cigarette. But in vain! If you do not provide this element with proper care, it can have an extremely negative impact on the vaping process as a whole.

An evaporator (atomizer, vaporizer, steam generator, smoke pro) is one of the main parts in an electronic cigarette, through which the vapor mixture is converted into vapor.

And, as you understand, its timely maintenance guarantees high-quality vaping. In this publication we will try to figure out how to clean the vaporizer of an electronic cigarette in order to provide it with quality care.

Basic rules for caring for your device

In order for your gadget to serve for a long time, you should provide it with proper care:

  1. Liquid and other components should be purchased only in specialized places.
  2. At the first problem, you need to clean the device. It is also recommended to do this after a specific period of use. Typically, cleaning is performed after 5-7 thousand puffs.
  3. Don't add too much liquid.
  4. If it is necessary to change the smoking taste, an unscheduled cleaning of the device is carried out.
  5. It is not recommended to take very deep breaths when using the device. This will cause the heating element to overheat and cause damage to the device.
  6. The device must remain charged. It is strictly forbidden to use the gadget in the cold. This greatly reduces its service life.
  7. The cartridge should not be used for more than 6-7 charges. Then the element filler must be replaced.
  8. Before cleaning the device and its components yourself, you should consult a specialist.

If you follow certain rules when using this device, then it will clearly last many times longer.

Caring for an electronic cigarette is as follows:

  • You can buy any liquids and components for the device only if the store is licensed or you are at least confident in it! Chinese online orders are a no-brainer if you want to ensure the longevity of your device.
  • You should develop the habit of cleaning your cigarette not only when it gets dirty and problems with operation begin, but also after a certain period, for example, monthly. But it is better to do this after a certain number of puffs, according to the recommendations of experts - after 6 thousand.
  • Do not fill the cartridge with more liquid than normal. This will not create more smoke, but will only damage the device.
  • Before changing the taste of the liquid, carry out a complete cleaning; this will not only save your device, but will also allow your receptors to fully enjoy the new aroma, without any impurities from the previous one.
  • When you “puff”, your breaths should not be very sharp and large, otherwise you can burn both the filter and the heating element itself.
  • Always keep the battery charge at the same level, and if possible, do not use a cigarette at temperatures below zero.
  • The cartridge can be filled approximately 8 times, after which it is worth considering replacing it.

Connoisseurs of pure flavor should have an idea of ​​how to care for an e-cigarette so as not to inhale bitterness and spoiled-tasting vapor. Otherwise, you will have to give up this habit or spend a lot of money on replacing components.

It is recommended to follow the rules for servicing electronic products:

  1. Mechanical cleaning of the surface and threaded connections from dirt and carbon deposits should be carried out every 3-4 days. This will prevent parts from jamming during disassembly.
  2. The clearomizer must be maintained in accordance with the requirements set out in the manufacturer's instructions. Do not use acid, alkali or household solvents to clean elements.
  3. Products should be stored at room temperature in a dry place. Overheating and excessive cooling lead to failure of batteries and changes in the composition of liquids in cartridges.
  4. You can wash the parts in a container with warm water. Strong water pressure can lead to deformation of parts and mechanisms.
  5. The devices do not have a large margin of safety. They must be protected from falls, impacts and strong horizontal pressure.
  6. When inhaling, do not take powerful puffs. This leads to combustion of the heating coil and clogging of the air channels.
  7. The battery should be charged at the same time every day. The product cannot be used for its intended purpose while charging.
  8. The ES should be protected from water getting on it: this leads to oxidation of the contacts and a short circuit of the battery terminals.

You need to use your e-cigarette correctly, as well as care for it.

Many people don’t even know how to do this, which leads to device failure and forces them to buy a new device.

How to care for an electronic cigarette - important rules:

  1. Do not wash your vape under a water tap. Too much pressure will cause the heating coil to bend, resulting in the entire evaporator having to be replaced.
  2. Using it involves disassembling it every 2-3 days to wipe the threads of the battery, base and evaporator.
  3. Do not leave the device for a long time in the cold or heat.
  4. Be careful when smoking, frequent puffs lead to overheating of the heating element, as a result it will quickly fail.
  5. Charge the device during, but not after, every time you use the device.
  6. Do not allow liquid to get on the battery, this will cause a short circuit, and if you are unlucky, the device will break.

You need to know how to care for your electronic cigarette, otherwise you will often have to change the device. When purchasing a device, ask the seller how to properly clean, wash, and even smoke.

Any incorrect actions lead to breakdowns.

All electronic cigarettes require proper care. They need to be washed, cleaned or blown out regularly. These procedures are not very long, but such operating rules will extend its service life.

And only with such care will the issue of changing the device disappear. And your existing e-cigarette will work well no matter how long you have it.

Methods for cleaning the evaporator

Caring for an atomizer (evaporator) involves washing, cleaning or burning it. This electronic cigarette module should be cleaned not only for prevention (this should be done at least once a week), but also if you decide to change the taste of the smoking e-liquid.

Flushing

Before you start rinsing the atomizer, remove the wick from the coil and thoroughly blow the atomizer to remove any remaining liquid. This is done from the side of the contact going to the battery, because there is a special reservoir in the area where the battery is connected. The purpose of the latter, designed on the principle of a “non-spill” inkwell, is to collect residual liquid and prevent it from getting onto the contact group. Therefore, it is possible to remove residual moisture by blowing only from this side of the miser.

After blowing, you should hold the part under a stream of warm water for several minutes so that it flows through the evaporator. Now blow the miser again and let it dry (contact side up) overnight, and blow it thoroughly again.

Cleaning

This procedure is more labor-intensive, and the need for it arises in case of prolonged use of the gadget without preventive cleaning. As a result, a layer of soot forms on the spiral, which cannot be removed by ordinary washing.

To clean a “coked” heater, you can use Coca-Cola or a vinegar solution (1 tablespoon of 9% vinegar per 1 glass of water). Soak the miser in any of the solutions recommended above for several hours, or better yet, overnight, then rinse it with water, rinse and dry as described earlier.

There is another very effective cleaning method - an ultrasonic bath. It can be easily purchased in online stores, and it is not expensive. According to user reviews, this is the best way to prevent contamination in misters.

Spiral burning

This is a rather risky procedure, and it is recommended only for experienced vapers, since this way you can completely “kill” the vaporizer. Its essence is to heat the miser coil red-hot and get rid of carbon deposits on it.

The burning procedure is as follows:

  • remove the wick and rinse the mister under running warm water, then blow it out;
  • screw the module to the battery pack;
  • press the power button for 4-5 seconds, but no more;
  • It is recommended to repeat the procedure 5 to 10 times until the coils are clear of carbon deposits;
  • After the miser has completely cooled down, blow it out.

After completing the cleaning procedure, insert a new wick into the coil, moisten it with liquid and assemble the device. After assembling the device and filling the cartridge with e-liquid, you can start vaping. The following video clearly demonstrates how to burn through the heating element of an atomizer.

Cleaning procedure

Firstly, the atomizer must cool down after use. Place it in a glass of very hot water and soak there for 15 minutes. We blow out excess water through the end that connects to the battery, and repeat the procedure one more time, after changing and heating the water. The main thing is that after rinsing there is as little water left as possible, so you can shake the atomizer properly.

Next, let it dry overnight or speed up the process with a hairdryer. After drying, connect it to the battery without inserting the cartridge or adding liquid.

Hold the button on the battery for 4 seconds. The spiral should begin to glow from the inside, and a hissing sound should be heard - this is the melting and evaporation of various deposits on it. Disconnect the battery and cool it. We repeat this procedure until the coil is clean (it starts to heat up very quickly).

Let the atomizer cool down. Then we drop four drops of e-liquid directly onto the bridge - slowly. Each drop should be well absorbed and only after that we drop the next one.

Attach the refilled cartridge and carefully pull it out. As soon as there is good steam, disconnect the cartridge. The atomizer is very dry after cleaning and will absorb liquid very quickly at first. If a burnt taste appears very quickly, you need to add a couple of drops of cigarette liquid directly to the bridge.

How to clean an e-cigarette atomizer

You can clean the atomizer often in this way; this will prevent serious contamination of the internal parts. The work is done this way:

  • Disassemble the electronic cigarette and remove the atomizer.
  • Place the part in a container of hot water and leave for an hour.
  • Blow out part of the device, then soak again for 2-3 hours.

After re-soaking, remove the atomizer from the water and dry in an upright position for at least 24 hours.

How often should you clean your electronic cigarette?

Some argue that cleaning an electronic cigarette is recommended every 2-5 thousand puffs. However, it is impossible not only to calculate this amount, but also to be precise in the calculations - some cigarettes will become clogged after 5 thousand puffs, and another - after 2 thousand. You can focus on the “symptoms” - the cigarette begins to drag poorly, a burning taste appears.

You can just rely on common sense. If you look, for example, at a new or just cleaned electric kettle. How long does it take for a visible layer of scale to form on it if used daily? Perhaps in 3-5 weeks. It's about the same with an electronic cigarette. A month of daily use, taking into account changing tastes, will likely require preventive cleaning of the atomizer, tank and mouthpiece.

How do you know when it's time to clean?

The device must always be kept clean. The formation of contaminants leads to irreversible deterioration of the atomizer’s performance, which can lead to breakdowns. It should be cleaned as often as possible, especially if you encounter at least one of these signs of clogging:

  • the vapor volume decreased very sharply and sensitively;
  • the supply of steam to the evaporator has stopped or is intermittent;
  • you spend more effort to vape through the atomizer;
  • the appearance of other odors or tastes, as well as if a burning taste appears.

What to avoid

  1. No need to use chemicals or solvents. It is impossible to get rid of the taste of a particular liquid you don’t like. Some of the liquid will still remain in the washcloth. The same goes for solvents.
  2. There is no need to overheat the atomizer during a dry run. If you overheat, the plastic ring inside the device may melt, as a result, the plastic may get on the coil, or greatly impede traction
  3. There is no need to do a dry run before soaking the atomizer in hot water. This may help improve performance for a short time, but it will deteriorate faster.
  4. There is no need to perform a dry run with a voltage higher than the working voltage for a given cigarette. Higher voltage may damage the coil
  5. There is no need to rinse the atomizer with running water. This may damage the internal parts of the device. Just soak in hot water.

Typically, e-liquids are based on polyethylene glycol (PEG), propylene glycol (PG) and vegetable glycerin (VG). All three of these substances are dehumidifiers.

The main reason why people mod electronic cigarettes is to increase battery life. You can use a larger and more energy-intensive battery - a cigarette.

The “mg” parameter on a pack of regular cigarettes and on a bottle of e-cigarette liquid mean completely different things. “Mg” on a pack of regular cigarettes indicates how much of the substance.

The evaporator is the most important part of the electronic cigarette, which is responsible for the formation of vapor. This is the main consumable that a steamer needs. Before using for the first time, allow a few minutes for the vaporizer to soak in the liquid. This will help prevent the wick from burning prematurely.

When using an electronic cigarette, it is important to follow basic operating rules to protect the device from premature contamination and damage:

  • read the instructions carefully;
  • purchase high-quality liquids for refilling only in specialized stores;
  • do not pour excessive amounts of liquid into the device;
  • do not take excessively deep breaths when inhaling to avoid overheating;
  • pause between puffs so as not to burn the cotton;
  • Avoid use in cold weather.

But even in this case, the evaporator sooner or later fails. Depending on the intensity of use, it can give you about 2 weeks of quality vaping.

Flavorings included in vaping mixtures often form a coating on the coils. If you feel an unpleasant taste and smell of burning, it means that carbon deposits have formed on the coil. The draft may also deteriorate, steam production may decrease, or the power supply may overheat. In these cases, the evaporator must be immediately replaced with a new one.

The Eleaf EC Replacement Evaporator - Ceramic Head is a ceramic based evaporator component. The advantages of the material are that it does not overheat the cotton, preventing it from burning. Ceramic improves the taste of steam and can work twice as long as a metal coil.

The replaceable SMOK V12 Prince-M4 evaporator operates at a power of up to 70W, which guarantees excellent flavor transfer and a fairly large amount of vapor. The replacement element is designed to replace the complete coil. You can buy an original evaporator for an atomizer from us at a reasonable cost.

There is an opinion that washing the evaporator with water, various liquids, alcohol, acids and subsequent burning can extend the service life of the evaporator. Practice shows that such a procedure is most often not effective; it is not possible to clean the carbon deposits efficiently. In addition, such a procedure reduces the resource by at least a third, and the efficiency of the electronic cigarette will become much worse. Washing a replacement evaporator at home will not help save money; it can often lead to damage to the entire device.

To replace, the atomizer is disconnected from the power source, the burnt-out evaporator is unscrewed, and a new one, specially selected for your model, is installed in its place.

In the Smoking online store you can purchase high-quality evaporators for various atomizers at affordable prices.

Both experienced and novice vapers need to know how to clean an electronic cigarette. Regardless of the device model, the principles of its maintenance are the same. Maintenance skills will come with experience, but information about the rules for operating the device must be known from the very beginning of its use.

Electronic cigarettes have become a priority for those who do not want to smoke tobacco, who are concerned about their health, or who simply want to enjoy the release of fragrant clouds of steam. These gadgets are a battery pack that powers a heating part, which is supplied with a special liquid mixture containing nicotine.

During use, contaminants accumulate in the vaporizer, affecting the taste of the vaping mixture. An unpleasant, bitter aftertaste appears and “gives off” a burnt taste. In this case, the relevance of the question arises: how to clean the fixer for an electronic cigarette? After all, the service life of the electronic device depends on the timeliness of cleaning the atomizer. We invite you to find out the answer to this important question for vapers, and how to provide the device with proper care that will prolong its life.

The absence of contamination is an important condition for the long service life of the device. If you clean the element in a timely manner, you will significantly save money due to the absence of the need to constantly change electronic components. Why constantly spend money on a purchase if you can avoid it?

If you do not clean the evaporator promptly, over time the liquid will stop flowing from its holes, which will affect the performance of the battery or damage it if it gets on it. If there is contamination, the inhaled vapors change the taste and aroma. Vapors may become bitter, less pronounced, or even unpleasant. “Notes” may also appear that are unusual for a recharged device.

Signs that require urgent cleaning of the vaporizer may include:

  • Low amount of vapor when compared to a new device.
  • Difficulty inhaling fumes.
  • No steam when traction.
  • The appearance of unusual tastes and odors in the vapor.

Due to these problems, the vape quickly deteriorates.

If you are performing the procedure for the first time, it is advisable to ask specialists how to do it correctly. They will tell you how to wash electronics without harming the gadget.

This procedure involves sequential simple manipulations. Cleaning the vaporizer should be done as follows:

  • Disassembling the device and disconnecting the spiral.
  • Blowing out the component parts of the device. If the contamination is minor, cleaning can be completed after the first event. But the contaminants may not be completely eliminated, then you need to move on to the next stage.
  • Rinsing the element under running warm water and blowing again.
  • Place the items on a towel or cloth for faster drying. It must be left in a vertical position.

You can also use another algorithm for flushing the evaporator of a vape device, and it is more effective:

  • Pour warm water into a container, or into a small bath.
  • Dip the vaporizer into water and leave it there for approximately 60 minutes.
  • Blow and rinse again in a container with water.
  • Blow again and dry. To make sure that the dirt is completely removed, blow out the evaporator again and place the elements vertically on a towel to dry (for several hours).
  • Attach the dried component to the vape.

Burning the vaporizer

If washing the electronic cigarette is definitely necessary using the burning process, it should be done as follows:

  • Wash the atomizer under a warm stream of running water and blow it out.
  • Press a single key and do not release it for 4-5 seconds. The procedure is carried out without a clearomizer (cartridge), so it needs to be repeated 5-10 times.
  • Allow the evaporator to cool and put on an empty clearomizer.
  • Do a few long, slow pulls until the steam disappears altogether.

Note: This method is not entirely safe for a vaping device. It can damage the vaporizer and permanently disable it.

Another effective option for removing contaminants in an atomizer. It is executed, not the previous ones, without sequence. You just need to place the device in an ultrasonic bath. This bath is successfully intended for delicate cleaning of delicate structures.

It can also be effectively cleaned chemically. Don’t be alarmed, everything is extremely simple and your email will not be harmed. You just need to prepare a solution from one tablespoon of vinegar and a glass of plain water, pour it into a container, put the device there and let it sit overnight. Then remove from the container, rinse and dry.

As you can see, everything is easy and simple to do, and most importantly, absolutely free, since you can clean the evaporator yourself, without the participation of professionals.

Cleaning the atomizer

An atomizer is otherwise called a vaporizer. It is he who, together with the power supply, ensures effective steam generation. There are 3 options for caring for this element of the electronic cigarette device:

  • washing;
  • ultrasonic bath;
  • burning

Before proceeding directly to washing the atomizer, it must be purged. This is done so that no residual liquid from the cartridge remains in the evaporator. You cannot clean a hot atomizer; it must cool down.

You can use hot water for rinsing. The evaporator is disconnected from the battery and immersed in liquid for 15-20 minutes. After this, remove and blow out the remaining water from it through the end that is used for attaching to the battery. Change the water and repeat the procedure one more time. After which the atomizer is placed in a vertical position and left to dry for 24 hours or more.

A heavily soiled evaporator cannot be washed with water. Instead, you need to use either vodka or diluted alcohol. In this case, the atomizer is left in the liquid for several hours. Vodka or alcohol can be replaced with Coca-Cola. There are a lot of enthusiastic reviews that this drink perfectly removes plaque. After soaking in an alcohol or other solution, the evaporator is washed with warm water and blown out.

This device is used for cleaning jewelry and electronic circuit boards. Therefore, it is in the arsenal of jewelers and mobile phone repairmen. An ultrasonic bath is an inexpensive device. It is easy to buy to make caring for your e-cigarette easier.

The burning procedure is performed at your own peril and risk. Most often they resort to it when it is impossible to properly rinse the evaporator coil. Sometimes burning is the only measure that allows you to return the atomizer to its former functionality. Burning should not be done frequently. The procedure is as follows:

  • the atomizer is disconnected from the battery;
  • blow it out;
  • rinse under running warm water;
  • blow again;
  • remove the cartridge and connect the atomizer to the battery;
  • if the device has such a function, set the operating voltage (voltage);
  • press the cigarette activation button and hold it in this position for 4-5 seconds;
  • allow it to cool down and press the activation button again;
  • repeat the procedure 10-15 times.

It is important not to press the button for more than 5 seconds, as this may damage the evaporator. After burning is complete, take the cooled atomizer and connect the empty cartridge. Perform a series of very slow puffs. The resulting steam is not inhaled, but released from the mouth so that it does not enter the lungs. After completing this procedure, fill the cartridge with liquid and begin normal vaping.

The atomizer is the heart of the cigarette, and performs the most important job in it - producing steam. Therefore, it is dirtier than other elements of the cigarette. The first thing you need to do after disconnecting the atomizer from the cigarette is to blow it out. This can be done without straining with a regular syringe. Then it is recommended to simply rinse the atomizer under running water.

It is advisable that the pressure is not strong, as there is a risk of damaging small parts, for example, the spiral. You can place the atomizer in water with a couple of drops of vinegar or half a teaspoon of citric acid, and leave it for a while - 1-2 hours, if the contamination is too strong. Then you should rinse it and dry it thoroughly with a paper towel, leaving it to “dry” for several hours.

You cannot use an atomizer that is not dry. Alcohol can be used as an alternative. There is no point in immersing the atomizer and its parts in alcohol - you just need to thoroughly wipe each part. It is important to note that cleaning should not be done with paper napkins or tissues.

How to clean the coil of an electronic cigarette atomizer

The atomizer coil must be cleaned regularly, otherwise an unpleasant aftertaste of accumulated burning will appear during smoking. You need:

  • Disassemble the accessory to gain access to the spiral.
  • Connect the device to charging.
  • By pressing the button, warm up the coil, periodically blowing off the exfoliated carbon from it.

To achieve a better effect, the heated coil can be lowered into a glass of water for 1–2 minutes, after releasing the button.

Battery and cartridge care

Of course, you should not wash the battery, however, if there is carbon deposits on the heating element, then there is carbon on the upper contacts of the battery, they just need to be wiped with a dry cloth. It is advisable not to use the e-cigarette during rain or snow and generally avoid getting the battery wet.

Maintenance of a power source lies in the rules for its use. They are easy to remember:

  • The first charge should last at least 12 hours:
  • the battery must always be fully charged;
  • Do not leave the battery discharged for a long period of time;
  • Do not allow the battery to be filled with liquid.

Maintenance consists of periodically wiping the power source with a dry cloth. A standard cartridge also does not require special attention. But it is important to know that before changing the fluid, it must be thoroughly washed and dried. You also need to make sure that the cartridge does not touch the atomizer coil. These rules for using an electronic cigarette will help extend its service life.

What should you not do when cleaning your e-cigarette?

You should not start cleaning the cigarette immediately after use. Water pouring onto hot or even just hot elements can, on the contrary, provoke the formation of a persistent coating and only aggravate the cleaning process.

Do not use any cleaning products to clean the cigarette. It is very difficult to wash off their smell, and it is almost impossible to get rid of chemical particles - eventually they will inevitably end up in the lungs.

If it is not possible to use alcohol, you can use vodka; in the absence of the latter, it is better to take an aqueous solution of vinegar or lemon juice. Various colognes and perfumes are not suitable for the same reasons as chemical cleaning products - excess chemicals will get into the lungs, and nothing will get rid of the smell.

How to clean the tank of an electronic cigarette

An element of an electronic accessory such as a liquid tank requires regular cleaning. You can do it like this:

  • Disassemble the device, disconnect the tank.
  • Place the part in a container of alcohol and leave for 6 hours.
  • Rinse the tank thoroughly under running water.
  • Dry the part, use a hairdryer if necessary.

This way you can clean not only the tank, but also the mouthpiece and the evaporator. Do not use any chemicals when cleaning, as they will leave a pungent odor. Treatment with alcohol is enough to keep these accessory parts in order.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]